根據的說法，將有用于大型電源系統的1級，2級和3級設備。通常，級主要是用于功率控制的配電中心，該配電中心通常安裝在變電站中，負責將電能分配到第二級。配電柜。第二級配電柜必須懲罰級配電柜分配的電能。第三級配電柜是光通量配電柜。由于我們分散了其布局，因此容量相對較低。配電柜可以為我們的生活提供安全保障，因此必須安裝配電柜，并根據情況將其隱藏在墻壁或其他地方。

安裝手車式高壓開關柜。安裝方法與固定式高壓開關柜的安裝方法基本相同，但區別在于要確保手推車的互換性。每個手推車型動觸頭必須設置一致，動觸頭和靜觸頭的中心必須均勻且緊密接觸，以確保互換性。配電柜廠家需要不定時的檢查二次回路的插頭和輔助觸點是否可靠焊接。電動或機械鎖定正確，因此手推車無法在關閉位置拉出。安全隔板易于打開和關閉，并且可以通過手推車進行伸縮。手車的接地裝置應與高壓配電柜的固定框架良好接觸。高低壓開關柜中的控制電纜已牢固固定，不會影響手推車的移動。

高-低-高頻轉換器：應用上下方法在中高壓環境中應用低壓或通用驅動器。原理是使用降壓變壓器將電網電壓降低到低壓逆變器的標稱或允許電壓輸入范圍。通過對逆變器進行轉換，然后將其從升壓變壓器轉換為所需的電動機，可以形成頻率和幅度可變的交流電源。電壓等級。如果運行中的變壓器有兩個或更多個接地故障，則在鐵芯的工作磁通周圍會形成短路匝。短路匝會產生大的渦流和循環電流，以加熱鐵芯，升高油溫，使邊緣碳化，并產生可燃氣體，從而導致輕質氣體的連續運動。如果接地不好，則循環可能是暫時的，從而導致輪輞油松動并碳化。此時，應通過色譜法對油進行分析，以確定故障的性質。